what to use to box in above kitchen cabinets
A upkeep friendly way to update your kitchen is to enclose space higher up kitchen cabinets!
Our builder course, kitchen cabinets were in need of a makeover. Instead of just painting them, we extended the cabinets to the ceiling.
This projection cost the states less than $60 and I think information technology made a significant departure in making the kitchen more than custom looking!
And I honey that in that location is no more dust collecting in the empty infinite that was above the cabinets!
Earlier PHOTO:
BEFORE PHOTO
We too scraped our popcorn ceiling and painted information technology, which didn't cost united states of america anything except the cost of the ceiling paint, and information technology improved the final await likewise!
Note, this postal service contains some affiliate links. For more info see my disclosures hither.
How to enclose space above kitchen cabinets:
** Note, the amount of boards you lot will need depends on the measurement of your wall(south).
Video Tutorial:
Subscribe to my YouTube Channel hither!
ane. Add 2×two boards to top of cabinets and ceiling
Add a 2×2 board to the superlative of your cabinets with 2″ brad nails and a brad nailer. Brand sure to adhere them 1/4″ back from the front end border of the cabinet. We held a flake piece of ane/iv″ plywood in front of the 2×two to line it up correctly when we clamped the two×2 downwardly.
Use a stud finder and mark where the studs are on the ceiling above the cabinets. Then, attach a two×2 with screws into the ceiling studs above the bottom two×2.
In order to attach our ceiling 2×2 in the correct spot and then that is was aligned with the lesser 2×2, we held a scrap slice of woods up confronting the bottom lath with a square and marked where information technology striking the ceiling. I'one thousand sure there are better ways to do this, but this way worked for united states!
Go on this step until you accept a finished adding the 2×2 boards along all of the cabinet tops and ceiling. Cut any two×2 boards to size with a miter saw where needed.
2. Add together ii×4 woods blocks spaced out between the 2×2 boards
If you lot are planning on adding crown molding like we did, and then 2×four blocks need to be added so that the crown has wood to blast through and secure to the "wall".
Most ceilings aren't perfectly level, so measure what the exact distance is between the two 2x2s at a few different spots and mark those spots on the wall. Nosotros spaced our boards about 18″ autonomously. Then, cut ii×4 boards to those sizes using a miter saw.
Add a pocket pigsty to each side of the ii×4 boards with a Kreg Jig. Likewise, it helped to number each board to call back exactly where it should get between the 2x2s.
Attach the 2x4s to the 2x2s with two 1/2″ Kreg screws. Note, the 2x4s don't have to be screwed in actually tight since you lot don't want them pulling on the 2x2s. You lot just want them tight enough to be secure. Brand sure to mark on the ceiling where these 2x4s are located and then you lot can boom the crown molding into them.
3. Add plywood to the 2×ii frame above the cabinets
Measure the distance between the ceiling and kitchen cabinets. Then, cut a piece of 1/4″ plywood to this size less a ane/iv″ then you can easily move it into the space.
Nosotros actually had our plywood cut at the domicile comeback store. But, yous can also cutting it with a table saw, circular saw, or Dremel. Only one side needs to be a really good, straight cutting since the other side will be covered by the crown molding.
Attach plywood to the 2x2s with 1 1/4″ brad nails.
If you take cabinets that are simply on one wall, this step is really easy. Simply, if your kitchen cabinets are like ours, where i corner cabinet is located on the adjacent wall, and so two pieces of plywood will join together to create an outside corner.
You can keep this elementary and just have the two edges join together next to each other. But, we wanted a cleaner corner border and decided to add together a 45 degree edge to the two ends for a clean joint. If you take a table saw this is easy to practise. Merely, nosotros don't so we used our router and our 45 degree chamfer router flake to add a 45 degree edge to the two board edges.
We yet concluded upwards with a small gap in the end between the boards, merely information technology all cleaned upwardly in the finish with some proficient caulking! You can come across a photograph of this corner close up in the side by side stride.
4. Add crown molding to space above the kitchen cabinets
The last footstep is to adhere the crown molding. Use brad nails and attach information technology along the bottom of the molding into the 2x4s and along the ceiling into the ceiling studs.
If you just have one wall of kitchen cabinets, then adding the crown molding is really easy and you don't need any fancy angled cuts, just direct cuts from wall to wall.
But, over again if your kitchen cabinets are like ours, with a corner cabinet on the side by side wall, then an inside corner and outside corner cut is needed for the crown molding.
Within corners are tough. Originally, I wanted to cope the inside corner cut for the cleanest and all-time plumbing fixtures look. But, we didn't have the right tools to exercise that.
We used the classic, no compound, mitered cut (verticaly nested) method for both the within and outside corner. I will have to do a dissever tutorial on crown molding, only this cut guide from Dewalt was super helpful and explains how to practice it. You lot basically plough your crown molding upside downwardly and cut at a 45 degree bending.
I also accept a clip of doing ane of the crown molding cuts in the video tutorial hither.
Our outside corner turned out well. Our inside corner took some fourth dimension and we had to make a few extra cuts at angles other than 45 degrees to go things to line up enough where we could caulk the imperfections.
5. Caulk, fill up nail holes, and paint
Fill up all nail holes with a lightweight spackle, permit it to dry, then lightly hand sand any backlog if needed.
Adjacent, caulk all gaps, seams, and corners with a paintable caulk.
Afterwards caulking, prime number the boards and plywood if they aren't already pre-primed.
Lastly, paint the enclosure and crown molding! We used the Benjamin Moore Accelerate paint, in White Dove with a satin sheen. The Advance line is neat for kitchen cabinets and high traffic areas, and so we volition be using it for our kitchen cabinets when we pigment them.
Our new extended kitchen cabinets with crown molding expect groovy and add graphic symbol to our standard kitchen. It makes the room feel taller and more blusterous likewise! It's astonishing how much of a difference it makes and for less than $lx, information technology actually is a big impact for a minor cost!
Well that'southward how to enclose infinite higher up kitchen cabinets!
Let'southward only compare once again to some other before photo :
Earlier PHOTO
And here's a shut upwardly of the finish work:
I can't wait to share our next project! Follow along on Instagram stories for sneak peeks of the kitchen makeover progress and follow along on YouTube for video tutorials of all the DIY projects!
Desire to save for later on?! Pivot IT Here:
Source: https://angelamariemade.com/how-to-enclose-the-space-above-kitchen-cabinets/
0 Response to "what to use to box in above kitchen cabinets"
Postar um comentário